incremental encoder supplier KN40 external diameter 40mm, ABZ ,
voltage output
Production Video
There are plenty of encoder video if you still have any doubts on
encoder, please email us directly or contact online service right
now.
At the same time, you could also visit our YOUTUBY page easily.
Most of the encoder series have videos for reference.
Product introduction for KN40 hollow shaft encoder
| Items | Basic parameters |
| Brand | HENGXIANG |
| Encoder type | Incremental encoder |
| External diameter | 40mm |
| Thickness | 20mm |
| Installation dimension | R17mm, R20mm;R23mm |
| Hollow shaft type | blind hole; through hole, taper hole,solid taper shaft |
| Solid shaft diameter | 10mm (taper shape) |
| Hollow shaft diameter | 6mm;8mm;9mm;9.52mm;10mm |
| Resolution | 1024;2048;2500;3600;5000;7200;10000;14400 |
| 1000/4;1000/6;1000/8;1024/4;1024/6；1024/8；2000/4；2000/6；2000/8；2048/4；2048/6;2048/8；2500/4；2500/6；2500/8;4096/4;4096/6;4096/8;5000/4;5000/6;5000/8 |
| Output phase | Phase A+,B+,Z+,A-,B-,Z-,U+,V+,W+,U-,V-,W- |
| Supply voltage | DC5V ; DC8--30V |
| Outlet type | Cable out from side |
| Output mode | NPN/PNP(Open Collector Output) |
| Voltage output |
| Push-pull output |
| line drive (26LS31) TTL |
| line drive(DC8-30V) HTL |
| TTL(DC5V) phase ABZ are back of phase UVW |
| Protection grade | IP40 |
| Shell Material | die cast aluminum |
| Certification | CE |
| package | Carton box |
| Net weight | About 90g (with package) |
Principle of encoder
Today most incremental encoders have a Push-Pull (HTL) or RS422
(TTL) output driver, these have replaced most of the older output
circuits like Open Collector NPN, Open Collector PNP, Voltage
Output.
Push-Pull (HTL) circuits, also known as Totem Pole, provide a
signal level which corresponds to the applied supply voltage. The
supply voltage typically ranges from 8 to 30 VDC.
With proper connections you can use the Push Pull interface to
replace true open collector circuits by using an external diode
connected in a way to limit the direction of the current for RS422
(TTL) circuits provide a constant 5 V signal level that is not
dependent on the supply voltage. Two supply voltage ranges can be
selected: From 4.75 to 5.5 VDC (can be used to replace open
collector output drivers) or from 8 to 30 VDC. Using differential
signals the output fully complies to the RS422 standard.
The differential outputs have the highest frequency response
capability and the best noise immunity. To ensure this the receiver
should also be a differential.
Replacement of Older Output Drivers
Applications
- Servo motion controller
- Gearbox
- DC garage door motor
- DC servo motor
- Stock driver
- PMDC geared motor
- Brushless dc motor
- Servo motor
- Drawing machine
- VFD
- Inverter
- Textile dyeing
- Leather machine
- Paper equipment
- Industrial machinery
Factory Encoder Production Capability
5000 pieces per month
-------- Production Line Capacity
50000 pieces per year
--------Actual Units Produced (Previous Year)
About Encoder Vibration
Vibration acting on an encoder always cause wrong pulse easily.
So we have to pay more attention to encoder working place.
The more pulse per round, the narrower groovy spacing of grating,
ore effect to encoder by vibration, when motor speed is low or even
stopped, vibration acting on encoder shaft or encoder shell would
cause grating vibration, in this way, encoder might show wrong
pulse signal.
