S25 mini solid encoder axial length 14.5mm diameter 25mm 600ppr for
robot
Our Service
- Quick response once received customer’s quotation query
- Professional engineer team, to solve your problems at any time
- Strictly inspection before shipment
- Various encoder models to be selected
- Short lead time
- High quality standard
Quick description of S25 rotary encoder
- Power supply voltage 5V-30V
- Pulse per turn: 36ppr to 2500ppr
- Radial cable or Axial cable output
- Sensing basic: photoelectric
- Protection level grade IP50
- Circuit output: NPN&PNP, voltage output, push-pull output, line
driver output
- Shaft length 14.5mm
- Resolution(PPR):Min 36ppr, Max 2500ppr
- Output Phase: ABZA-B-Z-
About Encoder Vibration
Vibration acting on an encoder always cause wrong pulse easily.
So we have to pay more attention to encoder working place.
The more pulse per round, the narrower groovy spacing of grating,
ore effect to encoder by vibration, when motor speed is low or even
stopped, vibration acting on encoder shaft or encoder shell would
cause grating vibration, in this way, encoder might show wrong
pulse signal.
Product Basis information
| Items | Basic parameters |
| External dimensions | External diameter: 25mm |
| Thickness: 30mm |
| Solid shaft diameter: 4mm(D shape) |
| Encoder type | Incremental encoder |
| Resolution | 20；25；36；50;60;100;200;250;256;300;360;400;500;512 |
| 600;625;720;1000;1024;1200;1250;1440;2000;2048;2500 |
| Output phase | Phase A,B,Z,A-,B-,Z- |
| Supply voltage | DC5V; DC8-30V |
| Outlet type | Cable out from side |
| Cable out from back |
| Output mode | NPN&PNP |
| Voltage output |
| Push-pull output |
| Difference output(TTL,HTL,RS422) |
| Environmental temperature | Operating temperature: -20~+80° (Non icing) |
| Storage temperature: -25~+85° (Non icing) |
| Environmental humanity | Operating and storage: 35~85%RH (non-condensing) |
| Protection grade | IP50 |
| Cable length | 1M (cable length could be added appropriately by |
| require, but it need payment individually) |
| Consumption current | 100mA Max |
| Allowable ripple | ≤3%rms |
| Insulation strength | AC500V 60s |
| Insulation resistance | 10MΩ |
| Mark to Space ratio | 45% to 55% |
| Top response Frequency | 100kHz Max |
| Shell Material | die cast aluminum |
| Bearing life | 1.5x109 revs at rated load(100000hrs at 2500RPM) |
| Shaft Material | Stainless steel |
ENCODER TECHNOLOGY THEORY
An incremental rotary encoder outputs a certain amount of Pulses
per Revolution. The higher this PPR number, the smaller the angle
between each pulse. This PPR number is fixed for ordinary
incremental encoders. Programmable incremental encoders can adjust
this value to a desired number by a software change.
Today most incremental encoders have a Push-Pull (HTL) or RS422
(TTL) output driver, these have replaced most of the older output
circuits like Open Collector NPN, Open Collector PNP, Voltage
Output.
Push-Pull (HTL) circuits, also known as Totem Pole, provide a
signal level which corresponds to the applied supply voltage. The
supply voltage typically ranges from 8 to 30 VDC.
With proper connections you can use the Push Pull interface to
replace true open collector circuits by using an external diode
connected in a way to limit the direction of the current for RS422
(TTL) circuits provide a constant 5 V signal level that is not
dependent on the supply voltage. Two supply voltage ranges can be
selected: From 4.75 to 5.5 VDC (can be used to replace open
collector output drivers) or from 8 to 30 VDC. Using differential
signals the output fully complies to the RS422 standard.
